Gun Riveter
 |
 REAL AIRCRAFT PARTS AIRCRAFT RIVETER RIVET GUN 1 4 NEW $64.97 Time Remaining: 28d 23h 24m Buy It Now for only: $64.97 |
 45 pc AIRCRAFT hand TOOL RIVNUT PULLER INSTALLER KIT riveter w 40 rivnuts gun $29.99 Time Remaining: 44m Buy It Now for only: $36.99 |
 NEW RIVET GUN W 6 PC RIVET SET KIT UP TO 1 4 RIVETS $77.35 Time Remaining: 20d 19h 8m Buy It Now for only: $77.35 |
 AIRCRAFT TOOL RIVNUT PULLER 3 n 1 riveter gun Threaded insert installer hand $32.99 Time Remaining: 4d 17h 7m Buy It Now for only: $32.99 |
 AIRCRAFT type hand TOOL RIVNUT PULLER 3 n 1 riveter gun Threaded insert $29.99 Time Remaining: 1d 10h 55m Buy It Now for only: $36.99 |
 New Rivet Gun 3X up to 3 16 rivets $40.49 Time Remaining: 17d 9h 40m Buy It Now for only: $40.49 |
 NEW RIVET GUN W RECON 5 PIECE RIVET SET KIT $68.39 Time Remaining: 20d 19h 7m Buy It Now for only: $68.39 |
 AIRCRAFT TOOL RIVNUT PULLER 3 n 1 riveter gun Threaded insert installer hand $32.99 Time Remaining: 4d 17h 14m Buy It Now for only: $32.99 |
 45 pc AIRCRAFT hand TOOL RIVNUT PULLER INSTALLER KIT riveter w 40 rivnuts gun $29.99 Time Remaining: 1d 10h 56m Buy It Now for only: $36.99 |
 AIRCRAFT TOOL RIVNUT PULLER 3 n 1 riveter gun Threaded insert installer hand $32.99 Time Remaining: 4d 17h 16m Buy It Now for only: $32.99 |
 401 Rivet gun Long Flush set Hi Lok punch machinist aircraft aviation tools $15.80 Time Remaining: 26d 23h 17m Buy It Now for only: $15.80 |
 AIRCRAFT type hand TOOL RIVNUT PULLER 3 n 1 riveter gun Threaded insert $29.99 Time Remaining: 5d 12h 41m Buy It Now for only: $36.99 |
 Aircraft Tools Rivet Set for Rivet Gun $23.99 Time Remaining: 11d 2h 51m Buy It Now for only: $23.99 |
 AIRCRAFT AIR HYDRAULIC RIVET GUN RIVETER NEW $44.97 Time Remaining: 3d 18h 6m Buy It Now for only: $44.97 |
Gun Riveter
How To Make A Personalized Scrapbooking Album
Here is a great scrapbooking album for you to make. It has a ring binder in the middle which will make it far easier to move your scrapbooking layouts about within the album.
Then I found an article on how to make your own album with a D-Ring in the middle, which makes putting your pages and layouts in order a breeze. It is much easier to file your scrapbooking layouts inside of a ring bound album. As the ones you buy in a store are not very creative, and not the right size, here is how you can make your own quite easily.
This is what you are going to need to construct your own album: 3mm MDF chipboard, a primer that you can sandpaper like Plasti-Kote, hand saw and face mask, sandpaper, Stanley knife, pencil, long ruler, rivet gun and rivets, 40mm D-Ring Binder mechanism, which you can take out of an unused file, strong fabric to cover your album, sewing machine and cotton to match your cover, punch to punch holes, corner rounder, spray adhesive, odds and ends like ribbon, craft knife, page protectors, rub-ons and other embellishments.
First of all you need to cut out your fabric as follows: One piece needs to be 14 x 13 inches and the other 14 x 18 inches. Press and sew a half inch seam allowance around all four sides of both pieces of fabric. You can either hand or machine sew this - your choice.
Next you will need to cut your chipboard to the correct size. If you are clever you will get the shop to do this for you. If doing it yourself, make sure to wear a face mask to avoid inhaling the fibres. Mark the pieces with pencil lines and use the Stanley knife to do the job for a clean cut before you use the saw.
Cut two of the pieces of wood to measure 400 x 330 mm and a spine of 330 x 70mm. Sand down the rough edges and position the binder mechanism in the proper place in the album. Mark where the holes should be and drill them out, or simply punch them out with your crop-a-dile if you have one.
Seal your wooden pieces with your primer and once dry lay the pieces out in a row and leave a 3mm gap between the pieces so that the file can fold once covered. If your fabric is very thick, you may need to use a slightly bigger gap.
Use the spray adhesive and glue the smaller piece of fabric onto the top of the file, making sure to position the fabric centred so that it covers the centre gaps. Smooth out any air bubbles.
Flip the album over and position the larger piece of material, ensuring you have an even amount of fabric hanging over the top and bottom of the file. Attach with spray adhesive and then turn over and fold the overhanging fabric over and glue down.
The fabric will now be holding the wooden file together on both sides.
Now that fabric is attached, you should be able to fold the wood over into an album shape. If you can't fold it over, then you haven't left enough space between the wooden pieces and may need to apply some gentle pressure to shift the wood into place before the glue dries.
To finish off the edges of the fabric, put some ribbon along the length of it and onto the inside of the file.
Feel where the holes are that you drilled at the start, and use your craft knife to make an incision at each hole, just big enough for the rivet to pass through. Pass the fat end through the hole from the outside so that the circular disk sits flush with the outside of the album. Place the binder mechanism over the rivet.
You will need to follow the instructions that come with your rivet gun and attach the binding mechanism to the album. The flat part of the binding mechanism must face outwards, and the curved part faces the spine of the album.
You can now round the corners of your new album with sandpaper or a round-it all and embellish the album to your hearts content.
About the Author
Michel Maling is a keen scrapbooker and enjoys learning new techniques and sharing ideas with others. You can see her blog at
http://scrapbookideasandsolutions.blogspot.com
Huck 353 Rivet Gun Riveter with Peterbilt Grill Fastener Nose Tip